Gowanda

Certifications  > AS9100 ISO 13485 ISO 9001

                                                      Customer Portal

CMF65SM Series — Wirewound

CMF65SM Series

hover to zoom image

Dimensional Specifications

View pdf

Series Data

For helpful information regarding the data in the following table please refer to the Notes section below the table. To request a sample, please indicate your choice in the columns to the right in the table. To check distributor stock, please click on a specific part number in the table.

Part number L µH Inductance
Tolerance
DCR OHMS
MAX
Current Rating
mA DC
Leakage Inductance
µH
Marking Request
Sample
CMF65-1003SM100±25%0.0058500.9Gowanda 100uH
CMF65-1803SM180±25%0.0077001.2Gowanda 180uH
CMF65-3303SM330±25%0.0154802.7Gowanda 330uH
CMF65-5003SM500±25%0.0233604.5Gowanda 500uH
CMF65-7503SM750±25%0.0343006.8Gowanda 750uH
CMF65-1004SM1000±25%0.0472408.6Gowanda 1000uH
CMF65-1804SM1800±25%0.08019013Gowanda 1800uH
CMF65-2204SM2200±25%0.10515019Gowanda 2200uH
CMF65-3304SM3300±25%0.16012018Gowanda 3300uH
CMF65-5004SM5000±25%0.2400.9526Gowanda 5004uH
CMF65-7504SM7500±25%0.3600.7535Gowanda 7504uH
CMF65-1005SM10000±25%0.5300.5545Gowanda 10000uH
CMF65-1205SM12000±25%0.7300.4555Gowanda 12000uH
CMF65-1505SM15000±25%1.1000.3568Gowanda 15000uH

Notes

All part numbers provide 25% tolerance on inductance
Custom designs are available to meet your specific requirements; please contact factory

Operating Temperature Range: -55°C to +125°C

Current Rating is based on a 40°C temperature rise from a 25°C ambient
    Note: Current is rated in both windings

Dielectric Withstanding Voltage (DWV) is 500 Vrms (winding to case top surface)

Excellent electromagnetic shielding

Leakage inductance tested as pins 1-2 with pins 3-4 shorted or at pins 3-4 with pins 1-2 shorted

Inductance and DCR is for each side of the winding

Windings balanced within 2%

Applications include reduction of AC line interference produced by switching power supplies (the opposing magnetic fluxes in the core serve to cancel in-phase noise signals appearing across the AC line) and noise suppression of DC circuits for switching regulators

Reflow Profiles

Please select the reflow soldering profile below that best suits your process. These reflow profiles represent typical industry standards. If you need additional assistance please contact Gowanda Electronics directly.

Reliability Data

Please note that reliability testing (HRIP Life Test) has been done for many, but not all, of Gowanda Electronics' products, in keeping with the needs of specific applications. Please use the information in this table as a guide; for additional assistance please contact Gowanda.

P/NTestTest ConditionsDurationPcs/TestedFailures
050AT3303SM Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
050KM3303SM Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
10M101K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
  Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 25 cycles 12 0
  Humidity per Mil-Std-202, Method 103 90-95% RH at 40 Degrees C 240 hrs 12 0
10M272K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
17S105K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
CC1008-101M Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
CC1008-471M Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
CF1008-151M Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SM3-010K Extended Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 10,000 hrs 10 0
  Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 5 cycles 12 0
  Humidity per Mil-Std-202, Method 103 90-95% RH at 40 Degrees C 240 hrs 12 0
  Overload per Mil-Std-15305, Para 4.8.10 1 1/2 Times Rated I 5 minutes 4 0
  Low Temp Storage per Mil-Std-15305, Para 4.8.14 Normal mounting and subjected to -65 C 96 hrs 4 0
  Resistance to solder heat Mil-Std-202, Method 210 SMI Reflow Thermal Profile (183 C PH, 250 C) 2 minutes 12 0
SM3-102K Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 10 0
  Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 5 cycles 12 0
  Humidity per Mil-Std-202, Method 103 90-95% RH at 40 Degrees C 240 hrs 12 0
  Overload per Mil-Std-15305, Para 4.8.10 1 1/2 Times Rated I 5 minutes 4 0
  Low Temp Storage per Mil-Std-15305, Para 4.8.14 Normal mounting and subjected to -65 C 96 hrs 4 0
  Resistance to solder heat Mil-Std-202, Method 210 SMI Reflow Thermal Profile (183 C PH, 250 C) 2 minutes 12 0
SMP3308-104M Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMP3013-102K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMP3013-104K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMP3315-103M Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
  Thermal Shock per Mil-Std-202, Method 107 -40 C to +70 C with 15 min dwell for saturation 1000 cycles 60 0
SMP3316-473M Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMP3316-104M Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMP5022-103M Vibration per Mil-Std-202, Method 201 Low Frequency Vibe in Z Direction 2 hrs 2 0
  Shock per Mil-Std-202, Method 213 Shock in Z Direction 3 Pulses 2 0
  Thermal Shock per Mil-Std-202 Method 107 -55 C to +125 C with 15 min dwell for saturation 100 cycles 2 0
  Resistance to solder heat Mil-Std-202, Method 210 Solder Dip 3 dips each 2 0
SMP5025-105K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMP8527-105K Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMRF1812-101J Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 6 0
  Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 200 cycles 6 0
  Humidity per Mil-Std-202, Method 103 85 C, 85% Humidity at Full Rated I 1000 hrs 6 0
SMRF1812-104J Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 6 0
  Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 200 cycles 6 0
  Humidity per Mil-Std-202, Method 103 85 C, 85% Humidity at Full Rated I 1000 hrs 6 0
SMRF5025-104K Life per Mil-Std-202, Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
SMRF5025-100K Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 50 cycles 10 0
  DWV per Mil-Std-202, Method 301 200 VDC between windings 30 seconds 10 0
  IR per Mil-Std-202, Method 302 500 VDC / 100 Mohm R min. core to windings 2 minutes 10 0
  Barometric Pressure per Mil-Std-202, Method 105 200 VDC at 70,000 feet altitude 60 seconds 10 0
  Solderability per Mil-Std-202, Method 208, Cat. 3 8 hrs of staem age and 1 solder dip 5 seconds 10 0
  High Temp Exposure per Mil-Prf-83446, Sec. 4.6.14 Normal mounting and subjected to +125 C 96 hrs 10 0
SMRF5025-823K Thermal Shock per Mil-Std-202, Method 107 -55 C to +125 C with 15 min dwell for saturation 50 cycles 10 0
  DWV per Mil-Std-202, Method 301 200 VDC between windings 60 Seconds 10 0
  IR per Mil-Std-202, Method 302 500 VDC / 100 Mohm R min. core to windings 2 minutes 10 0
  Barometric Pressure per Mil-Std-202, Method 105 DWV (200 VDC) at 70,000 feet altitude 60 seconds 10 0
  Solderability per Mil-Std-202, Method 208, Cat. 3 8 hrs of staem age and 1 solder dip 5 seconds 10 0
  High Temp Exposure per Mil-Prf-83446, Sec. 4.6.14 Normal mounting and subjected to +125 C 96 hrs 10 0
SMT45-303 Life per Mil-Std-202 Method 108 90 C ambient, Full Rated I, 75% on, 25% off 2,000 hrs 10 0
MAXIMUM QUANTITY PER REEL REEL DIAMETER: in. (mm) PITCH BETWEEN PARTS: in. (mm) TAPE WIDTH: in. (mm) CLASS #
350 13 (330.2) 1.10 (28) 0.945 (24)
Standard Termination Finishes Lead Free Termination Finishes
Sn63Pb37 Sn99.3Cu0.7